 |
 |
 |
 |
 |
 |
 |
 |
 |
RS-200 Benchtop Router Table
Cabinet
Cabinet is 24" x 19" x 16" tall and constructed of Birch veneer core plywood
trimmed in solid Oak. Inside construction MDF. 2 drawers hold 26, ½" bits, 2
drawers hold 48, ¼" bits and 1 wrench drawer. Side 2 ½"dust collector port
draws dust through the fence and also ventilates the router motor. Two 120-
volt receptacles in back allow you to connect your router and dust collector.
The front On/Off switch [recessed for safety] operates both router and dust
collection. Equipped with 6’ Power cord.
STEEL REINFORCED TOP
The top construction starts with 22 x 30 x 3/4” MDF core Melamine. Unlike the
common wood top that could warp over time our tops have Two steel support
struts that run the full width of the top to insure its flat and stays that way for
years of service. The edges are thickened to 1-1/2” to securely mount the
steel struts plus the extra heft for fixture clamping all trimmed with Oak.
Directly under the router opening there are two more 3/4” wide steel bars
secured into the top of the cabinet to support even the largest routers
without worry. What you end up with is a top that is 1-1/2” thick in all the
stressed areas, 3/4” MDF and 3/4” Steel !
The 9-¼”x 11-¾”x 3/8" opening in top is sized to accept many of the most
popular router lifts. Clear 3/8”Acrylic plate with 6 leveling screws ships blank
for custom fitting to routers up to 3 1/4 hp from All manufacturers. Aluminum
3/8"x 3/4" miter track runs the width of the top that accepts standard miter
gauges from most tablesaws. Plate is offset to the backside of the table to
allow more working surface up front where its needed.
Steel reinforced router opening in top has been weight tested to 200 pounds.
It will hold any router combination you choose to install.
FENCE
The fence is constructed of 9 ply cabinet grade 1/2” Baltic Birch using glue,
brads and screws with enough supports to insure it stays square. Fence is
mounted to the table with large Star Shaped comfort grip knobs. A few turns
of the large knobs and the fence lifts off, leaving a smooth unobstructed
table for pattern and freehand work.
At 4 1/4" tall the segmented fence is ideal for control and accuracy in vertical
routing operations. The top section has a "T" slot along its length, that accept
5/16 T-bolts, for attachments such as feather boards, hold downs, stop blocks
& guards. T-bolts are not an expensive specialty item available only through
woodworking stores as most people believe, they are readily available at any
home center or lumberyard. They call them "Toilet Flange Bolts" about .30
each. The lower section opens from 0" to 3 1/2" for the safe use of larger bits.
Fence adjusts Forward and Back 5". Dust is collected through the fence from
under the table surface.
Shipping
Shipping via FedEx Ground in continental United States"Lower 48" ONLY !
$225.00 plus $69.00 shipping.
Table will ship within 10 business days of receiving payment.
Cabinet is 24" x 19" x 16" tall and constructed of Birch veneer core plywood
trimmed in solid Oak. Inside construction MDF. 2 drawers hold 26, ½" bits, 2
drawers hold 48, ¼" bits and 1 wrench drawer. Side 2 ½"dust collector port
draws dust through the fence and also ventilates the router motor. Two 120-
volt receptacles in back allow you to connect your router and dust collector.
The front On/Off switch [recessed for safety] operates both router and dust
collection. Equipped with 6’ Power cord.
STEEL REINFORCED TOP
The top construction starts with 22 x 30 x 3/4” MDF core Melamine. Unlike the
common wood top that could warp over time our tops have Two steel support
struts that run the full width of the top to insure its flat and stays that way for
years of service. The edges are thickened to 1-1/2” to securely mount the
steel struts plus the extra heft for fixture clamping all trimmed with Oak.
Directly under the router opening there are two more 3/4” wide steel bars
secured into the top of the cabinet to support even the largest routers
without worry. What you end up with is a top that is 1-1/2” thick in all the
stressed areas, 3/4” MDF and 3/4” Steel !
The 9-¼”x 11-¾”x 3/8" opening in top is sized to accept many of the most
popular router lifts. Clear 3/8”Acrylic plate with 6 leveling screws ships blank
for custom fitting to routers up to 3 1/4 hp from All manufacturers. Aluminum
3/8"x 3/4" miter track runs the width of the top that accepts standard miter
gauges from most tablesaws. Plate is offset to the backside of the table to
allow more working surface up front where its needed.
Steel reinforced router opening in top has been weight tested to 200 pounds.
It will hold any router combination you choose to install.
FENCE
The fence is constructed of 9 ply cabinet grade 1/2” Baltic Birch using glue,
brads and screws with enough supports to insure it stays square. Fence is
mounted to the table with large Star Shaped comfort grip knobs. A few turns
of the large knobs and the fence lifts off, leaving a smooth unobstructed
table for pattern and freehand work.
At 4 1/4" tall the segmented fence is ideal for control and accuracy in vertical
routing operations. The top section has a "T" slot along its length, that accept
5/16 T-bolts, for attachments such as feather boards, hold downs, stop blocks
& guards. T-bolts are not an expensive specialty item available only through
woodworking stores as most people believe, they are readily available at any
home center or lumberyard. They call them "Toilet Flange Bolts" about .30
each. The lower section opens from 0" to 3 1/2" for the safe use of larger bits.
Fence adjusts Forward and Back 5". Dust is collected through the fence from
under the table surface.
Shipping
Shipping via FedEx Ground in continental United States"Lower 48" ONLY !
$225.00 plus $69.00 shipping.
Table will ship within 10 business days of receiving payment.
